High-concentration graphene dispersions with minimal stabilizer: a scaffold for enzyme immobilization for glucose oxidation.

Modified acrylate polymers are able to effectively exfoliate and stabilize pristine graphene nanosheets in aqueous media. Starting with pre-exfoliated graphite greatly promotes the exfoliation level. The graphene concentration is significantly increased up to 11 mg mL(-1) by vacuum evaporation of the solvent from the dispersions under ambient temperature. TEM shows that 75 % of the flakes have fewer than five layers with about 18 % of the flakes consisting of monolayers. Importantly, a successive centrifugation and redispersion strategy is developed to enable the formation of dispersions with exceptionally high graphene-to-stabilizer ratio. Characterization by high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and Raman spectroscopy shows the flakes to be of high quality with very low levels of defects. These dispersions can act as a scaffold for the immobilization of enzymes applied, for example, in glucose oxidation. The electrochemical current density was significantly enhanced to be approximately six times higher than an electrode in the absence of graphene, thus showing potential applications in enzymatic biofuel cells.

Surface-Modified TiO2 Photocatalysts Prepared by a Photosynthetic Route: Mechanism, Enhancement, and Limits.

Surface-modified TiO2 photocatalysts were synthesized by a photosynthetic route involving visible-light-induced (λ>455 nm) activation of benzene and toluene at the surface of TiO2 leading to the formation of carbonaceous polymeric deposits. IR spectroscopic and photoelectrochemical experiments showed that the mechanism of the photosynthetic reactions involves intra-bandgap surface states at TiO2 related to surface OH groups interacting with adsorbed aromatic molecules. The photosynthesized surface-modified TiO2 materials exhibited enhanced activity, relative to pristine TiO2 , in photocatalytic degradation (and complete mineralization) of 4-chlorophenol. The improvement was pronounced particularly under visible-light (λ>455 nm) irradiation with the relative initial photodegradation rate enhanced by a factor of four. The surface-modified photocatalysts exhibited good stability under the operating conditions, and the optimum carbon content was approximately 0.5 wt %. Mechanistic studies showed that the enhanced visible-light photodegradation of 4-chlorophenol is due to modified surface-adsorption properties that facilitate formation of a surface complex between titania and 4-chlorophenol, rather than due to any sensitizing effect of the carbonaceous deposits. The study highlights the importance of considering the interaction between pollutant molecules and the photocatalyst surface in heterogeneous photocatalysis, and possibly opens up a route for photosynthesis of further surface-modified photocatalysts with tuned surface properties.

Optimization of a membraneless glucose/oxygen enzymatic fuel cell based on a bioanode with high coulombic efficiency and current density.

After initial testing and optimization of anode biocatalysts, a membraneless glucose/oxygen enzymatic biofuel cell possessing high coulombic efficiency and power output was fabricated and characterized. Two sugar oxidizing enzymes, namely, pyranose dehydrogenase from Agaricus meleagris (AmPDH) and flavodehydrogenase domains of various cellobiose dehydrogenases (DH(CDH)) were tested during the pre-screening. The enzymes were mixed, "wired" and entrapped in a low-potential Os-complex-modified redox-polymer hydrogel immobilized on graphite. This anode was used in combination with a cathode based on bilirubin oxidase from Myrothecium verrucaria adsorbed on graphite. Optimization showed that the current density for the mixed enzyme electrode could be further improved by using a genetically engineered variant of the non-glycosylated flavodehydrogenase domain of cellobiose dehydrogenase from Corynascus thermophilus expressed in E. coli (ngDH(CtCDHC310Y)) with a high glucose-turnover rate in combination with an Os-complex-modified redox polymer with a high concentration of Os complexes as well as a low-density graphite electrode. The optimized biofuel cell with the AmPDH/ngDH(CtCDHC310Y) anode showed not only a similar maximum voltage as with the biofuel cell based only on the ngDH(CtCDHC310Y) anode (0.55 V) but also a substantially improved maximum power output (20 µW cm(-2)) at 300 mV cell voltage in air-saturated physiological buffer. Most importantly, the estimated half-life of the mixed biofuel cell can reach up to 12 h, which is apparently longer than that of a biofuel cell in which the bioanode is based on only one single enzyme.

Mutual enhancement of the current density and the coulombic efficiency for a bioanode by entrapping bi-enzymes with Os-complex modified electrodeposition paints.

A bioanode with high current density and coulombic efficiency was developed by co-immobilization of pyranose dehydrogenase from Agaricus meleagris (AmPDH) with the dehydrogenase domain of cellobiose dehydrogenase from Corynascus thermophiles (recDHCtCDH) expressed recombinantly in Escherichia coli. The two enzymes were entrapped in Os-complex modified electrodeposition polymers (Os-EDPs) with specifically adapted redox potential by means of chemical co-deposition. AmPDH oxidizes glucose at both the C2 and C3 positions whereas recDHCtCDH oxidizes glucose only at the C1 position. Electrochemical measurements reveal that maximally 6 electrons can be harvested from one glucose molecule at the two-enzyme anode via a cascade reaction, as AmPDH oxidizes the products formed from of the recDHCtCDH catalyzed substrate oxidation and vice versa. Furthermore, a significant increase in current density can be obtained by combining AmPDH and recDHCtCDH in a single modified electrode. We propose the use of this bioanode in biofuel cells with increased current density and coulombic efficiency.

A new synthesis route for Os-complex modified redox polymers for potential biofuel cell applications.

A new synthesis route for Os-complex modified redox polymers was developed. Instead of ligand exchange reactions for coordinative binding of suitable precursor Os-complexes at the polymer, Os-complexes already exhibiting the final ligand shell containing a suitable functional group were bound to the polymer via an epoxide opening reaction. By separation of the polymer synthesis from the ligand exchange reaction at the Os-complex, the modification of the same polymer backbone with different Os-complexes or the binding of the same Os-complex to a number of different polymer backbones becomes feasible. In addition, the Os-complex can be purified and characterized prior to its binding to the polymer. In order to further understand and optimize suitable enzyme/redox polymer systems concerning their potential application in biosensors or biofuel cells, a series of redox polymers was synthesized and used as immobilization matrix for Trametes hirsuta laccase. The properties of the obtained biofuel cell cathodes were compared with similar biocatalytic interfaces derived from redox polymers obtained via ligand exchange reaction of the parent Os-complex with a ligand integrated into the polymer backbone during the polymer synthesis.

Electron transfer between genetically modified Hansenula polymorpha yeast cells and electrode surfaces via Os-complex modified redox polymers.

Graphite electrodes modified with redox-polymer-entrapped yeast cells were investigated with respect to possible electron-transfer pathways between cytosolic redox enzymes and the electrode surface. Either wild-type or genetically modified Hansenula polymorpha yeast cells over-expressing flavocytochrome b2 (FC b(2) ) were integrated into Os-complex modified electrodeposition polymers. Upon increasing the L-lactate concentration, an increase in the current was only detected in the case of the genetically modified cells. The overexpression of FC b(2) and the related amplification of the FC b(2) /L-lactate reaction cycle was found to be necessary to provide sufficient charge to the electron-exchange network in order to facilitate sufficient electrochemical coupling between the cells, via the redox polymer, to the electrode. The close contact of the Os-complex modified polymer to the cell wall appeared to be a prerequisite for electrically wiring the cytosolic FC b(2) /L-lactate redox activity and suggests the critical involvement of a plasma membrane redox system. Insights in the functioning of whole-cell-based bioelectrochemical systems have to be considered for the successful design of whole-cell biosensors or microbial biofuel cells.

Redox electrodeposition polymers: adaptation of the redox potential of polymer-bound Os complexes for bioanalytical applications.

The design of polymers carrying suitable ligands for coordinating Os complexes in ligand exchange reactions against labile chloro ligands is a strategy for the synthesis of redox polymers with bound Os centers which exhibit a wide variation in their redox potential. This strategy is applied to polymers with an additional variation of the properties of the polymer backbone with respect to pH-dependent solubility, monomer composition, hydrophilicity etc. A library of Os-complex-modified electrodeposition polymers was synthesized and initially tested with respect to their electron-transfer ability in combination with enzymes such as glucose oxidase, cellobiose dehydrogenase, and PQQ-dependent glucose dehydrogenase entrapped during the pH-induced deposition process. The different polymer-bound Os complexes in a library containing 50 different redox polymers allowed the statistical evaluation of the impact of an individual ligand to the overall redox potential of an Os complex. Using a simple linear regression algorithm prediction of the redox potential of Os complexes becomes feasible. Thus, a redox polymer can now be designed to optimally interact in electron-transfer reactions with a selected enzyme.

Electrodeposition polymers as immobilization matrices in amperometric biosensors: improved polymer synthesis and biosensor fabrication.

Electrodeposition polymers can be precipitated on electrode surfaces upon electrochemical-induced modulations of the pH value in the diffusion zone in front of the electrode. The formed polymer films can be used as immobilization matrices in amperometric biosensors. In order to rationally control the thus obtained biosensor properties, it is indispensable to develop strategies for the reproducible synthesis of electrodeposition polymers as well as methods for the non-manual and reproducible sensor fabrication. Based on instrumental developments such as a specifically designed parallel synthesizer with improved stirring and temperature control, an automatic pipetting robot for the preparation of the monomer mixtures and controlled removal of polymerization inhibitors, the reproducible synthesis of libraries of electrodeposition polymers was achieved. Moreover, the polymerization process could be monitored using in-line thermocouples, and it could be shown that the chosen strategies led to reproducible polymerization reactions. By adaptation of an electrochemical robotic system integrating a Au microtiter plate and automatic electrode cleaning by means of a polishing wheel reproducible biosensor fabrication using glucose oxidase as a model enzyme could be demonstrated. These results open the route for the rational development of biosensors and control of the sensor properties by choosing specifically designed electrodeposition polymers.

Parallel synthesis of libraries of anodic and cathodic functionalized electrodeposition paints as immobilization matrix for amperometric biosensors.

The integration of flexible anchoring groups bearing imidazolyl or pyridyl substituents into the structure of electrodeposition paints (EDP) is the basis for the parallel synthesis of a library containing 107 members of different cathodic and anodic EDPs with a high variation in polymer properties. The obtained EDPs were used as immobilization matrix for biosensor fabrication using glucose oxidase as a model enzyme. Amperometric glucose sensors based on the different EDPs showed a wide variation in their sensor characteristics with respect to the apparent Michaelis-Menten constant (KM(app)) representing the linear measuring range and the maximum current (Imax(app)). Based on these results first assumptions concerning the impact of different side chains in the EDP on the expected biosensor properties could be obtained allowing for an improved rational optimization of EDPs used as immobilization matrix in amperometric biosensors.